Advice opinions please

[AndrewA]

Thanks Geoff - will investigate but think it's had slightly warmer cams and an Eldebrock but will check. The stroker kit seems the way to go for a serious jump in power and torque.My main concern on the car I'm considering is that apparently both outer sills are corroded and holed & what are described as hockey sticks are missing from the wing bay floors. The chassis edge in front of the battery bay and spare wheel bay is pulling apart. I'm assuming sills are sills so nothing too much to worry about there, not sure what they mean about jolly hockey sticks and I guess the other bit means water has got into the leading edge of the chassis and it's starting to pull apart - again nothing too horrendous unless it's gone too far?
Cheers
Andrew

[PEU186F]

One generality to beware of is that when you are new to them the V8 Bristols, even if they are actually in quite a bad state, have so much torque that they cannot help but impress somebody who is used to lesser vehicles. So beware, even though one might seem great at first acquaintance, there may be a long way to go before it is actually up to the mark.

I speak from experience

If you look at the contemporary tests there is actually not a lot of difference in the speed vs time acceleration tests for the 410 and the 411. There isn't a lot of difference in top speed either.

My 410, which runs on the wider 411 wheels, was quite capable of snaking its rear wheels at 60 when passing another vehicle under acceleration on a wet road, even though at that time I wondered about its breathing. I finally got fed up with broken manifolds and caused SLJ to fit their free flow exhaust manifolds. It now fairly romps away - I haven't met a damp road since for various other reasons but one knows ones got there when a member of SLJ's staff comes back with a broad smile on his face and the comment "goes well, doesn't she"

There is, or there should be, a very considerable amount of steel in the sills. I recently had to had my nearside sill cut out and replaced and I was quite reassured by how much metal there is there to protect occupants from a side impact.

I would be rather cautious of a car with lots of bolt ons and a poor structure, it seems to me that money may have been spent in the wrong place. At the very least get a price for the work that might need to be done. After all, once you're hooked, you're hooked and you'll then be on the line for a very long time

[AndrewA]

Thank you for the advice which I will keep in mind. As you suggest, it is easy for heart to rule head on first acquaintance!
Are there any downsides to the free flow manifolds in terms of noise or are they as quiet as the standard item?
Regards
Andrew

[PEU186F]

Having done three quarters of an alpine tour, including the Stelvio, with a one broken manifold and the other blowing I am hardly qualified to judge the comparison. By the time we left her at SLJ the broken manifold was completely detached so the noise was horrendous. But I can confirm that I am entirely happy with the free flow manifolds, they don't seem noisy to me, honest.

The original 410 front exhaust hangings were far too rigid, engine torque then making the manifolds extremely vulnerable as most of the torque ended up being taken by the manifolds. The much improved 411 system is now adopted.

Another piece of advice: the Stelvio, a 410 and a stiff neck don't mix. There is also only loads of tatty stalls and dirty snow at the top. As for the bloody cyclists!!! They CYCLE up it. I was so discombobulated I could only drink a bottle of cold water at the top. See photo in my earlier posting 411 front disc brakes.

Roger

[AndrewA]

Noted re Stelvio!
Thanks for clearing that up about the manifolds and the point about the exhausts mountings/hangings.
Andrew

[stovo]

Andrew,
hoping this link will work for you. Some 410 pics for your contemplation in isolation..

My 410 is the former Claude Lewenz left hand drive 'Gantt' car. Restored by the factory and lightly breathed upon. Lovely car to drive. Swift and quiet with a nice growl when extended. One thing I'd change if I did it again would be to go to a 4-speed box but it's ok for most uses in the USA.

https://www.flickr.com/photos/107289...57637155099704

I also had a Brigand for a while. 5.9 liters and turbo made for swift progress but it didn't get enough use to stay in tune. When it had been in the tender care of Bristol Cars it ran superbly but the 360 injected engine is a way better long term proposition.

A 410 / early 411 still carries a lot of the charm of the earlier generation and fewer of the parts-bin interior bits. Best of all worlds imho :-)

Wishing you the best with your search.

[AndrewA]

Morning Steve - what a stunning car and the colour suits it very well. Love the "London Meat Company" shot - excellent!
Appreciate the feedback on the driving experience, and the useful comment about the 4 speed.
Thanks
Andrew

[Kevin H]

Originally Posted by stovo

Andrew,
Some 410 pics for your contemplation in isolation..

Steve, it appears you have plumbed in a new fuel line directly into the bottom of the reserve section of the tank, and is that an inline electric fuel pump?