405 Heater Box Removal

[peterf]

Thanks Geoff for the suggestion, the thought did cross my mind but what to do with all those bits of unwanted Bristol 405 ???? besides I would still want to hang onto the heater box as a memento!!

However with some persistence the problem is now solved and I have one heater box removed and the heater radiator ready for the tanks to be removed and the entire radiator and tubes cleaned.

For those interested here is how it was done,

Firstly It is important to understand that the demister tubes exit the heater box at a slight upwards angle.
The two holes in the bulk head that the demister tubes pass through are elongated upwards and towards the driver’s side.

The workshop manual says to disconnect the speedo cable, which would suggest that you remove the heater box from that side BUT this could not work because the oil pressure line is immediately in the way as is the auxiliary light socket and the hump for the steering column. No mention of removing the oil line or the light socket in the workshop manual.

Because of the tube angle when I cut the tube end off ( Straight ) with just a metal saw blade I ended up with one side being 3-4 mm and the other side being about 7mm, which as it turned out was pretty close to what I estimated should be removed (5mm -10mm) this amount would still easily allow the rubber elbow to be refitted. It was still a bit tricky to remove the unit via the passenger side where I disconnected the cable to the fuel mixture system and pulled it back through the firewall and partly through the bulk head so as to not impede the heater box movement at all. I had already removed the HMV radio power unit which is located immediately to the left of the heater box but that is a simple procedure. I taped up the edge of the bonnet opening to prevent any scratches and then finally I was in possession of one liberated heater box.

To make it a little easier to refit I will look at trimming the demister tubes a little more and perhaps work out a tube insert mechanism which can be inserted/withdrawn from within the cabin, Not that I think I should ever have to do this again.

The next step is to take the heater radiator to a radiator specialist for a tanks off cleaning and then I need to service the water valve. I hope this info assists someone else in the future.

Cheers all

Peter

[BRIGHAM G]

Thank you Peter,
I am just about to remove the box on my 405 and had no idea it would be difficult. Your postings are going to be a great help to me.
Thank you again,
Best wishes,Gerald.

[Stuart]

Just put mine back in....

There is a story that Bristol made the 405 by first hanging the heater box from the work's ceiling and then building the rest of the car around it.... Anyway...

One hint for removal re-insertion is to force the forward bulkhead forward about 6 - 10mm with a scissor jack, that's what I had to do to get enough clearance, didn't seem to damage the b'head....

I just took the heater assembly to bits, easy, then cleaned out the dead animal life from the air side, removed the radiator and hosed hot water through it with the radiator at various angles to get at all of it... I think there was more dead water life than air...

I didn't need to cut anything from the air vent pipes, however the rest of my car is in bits so it's fairly easy to get at most of it....

My water valve was stuffed so I got a similar one from the local MG spares guy, it's a common BL type... Don't forget the little O ring that seals it all...

I have pics of the heater controls setup and water valve if needed...

Have fun, Stuart

[peterf]

Hi Stuart,

Could you please post the photos you mentioned, I am looking to replace my water valve as well so could you also provide the specific part number and the model of MG car that your valve is from, all information very much appreciated.

Cheers

Peter

[devadmin]

This thread might be useful;

http://www.bristolcars.info/forums/8...ter-valve.html

[Kevin H]

If your heater valve has two control levers it is the same as that used on a Triumph 2000 (1963-69). I just checked in the Triumph workshop manual

[GREG]

Ashley Hinton - Manufacturer of Body Panels, Heaters and Accessories for MG and Austin Healey

This company stock the valve and many other parts for various Bristol's £28 on eBay