Oil consumption

[peterg]

Sure the engine leaks, it's a Bristol! but no, not much. When we got to Dunkirk the plume of smoke on tick over was about 10 feet long (no wind) and other drivers had commented on the amount of smoke coming out of the car on the run over the weekend.

This was the first run over 40 miles as mostly it is only driven from home to where I keep it due to the constant problems I have had. It has also had numerous oil changes (aprox every 400 miles), so I didn't check the oil level very often.

I was told about 100 hours and this matched the costs from another repairer.

The engine runs rather well once off tick over with no misfiring. Performance wise this is the only Bristol I have driven. It seems a little slow off the mark but quite perky once it is rolling along. I red line it at 4,000 rpm.

[Geoff Kingston]

To do the job with the engine in place the cylinder head has to come off, if the car had new liners and pistons 20000 miles before you had the work done on the engine I can understand why the specialist left everything in place but that is taking a risk which in this case does not seem to have paid off, especially when everything else was presumably already apart.
Many years ago I had a 401 with new liners pistons and rings, it was not getting much use and after an accident it stood for about six months and the engine stuck, we eventually freed it off and following an oil and filter change it ran well but still had but a tendency to oil up the plugs on 5 and 6. I suspected broken rings so in the end we took the engine out, head and sump off, rods and pistons out and sure enough there were broken rings on pistons 5 and 6.
As the pistons and liners were perfect, the cylinders were lightly honed and all we had to replace were the rings and gaskets.
As I said it was oiling the plugs before it stuck so the problem may have occurred previously or the rings might have even been damaged on installation, before we finally took it apart it stuck slightly on two other occasions, it was a tight engine that did not like being stood.
As your car has covered a low annual mileage after the liners and pistons were replaced I would be inclined to suspect a ring problem and If it were mine I would look seriously at replacing the rings with the engine in place. Unless the car has suffered piston damage from broken rings or some other cause I would get the usual checks carried out and reuse them as well, just give the bores a very light hone and fit new high quality rings.
Obviously ensure the rods and pistons go back in the correct order i.e the cylinder they came out of.
I had a oil burning situation suddenly develop on a Bentley S2 a few years ago after a 200 mile trip, my mechanic discovered that two of the valve guides had worked loose allowing oil to leak into the combustion chambers, the guides had not been installed properly so I had to get them replaced and we also fitted improved valve seals at the same time and had no further problems. I have not come across this on a Bristol engine but it might be worth checking while the head is off.
One final thought I assume you are using the correct grade of oil to a classic formulation as modern oils can cause high oil consumption and low oil pressure problems on some older engines.

[Kevin H]

Have you done any investigation yet Peter, such as inspecting spark plugs or doing a compression test?

[peterg]

Got it checked today. All pots 100 to 110 psi, number 4 pot heavily oiled.

They also said the clutch was close to slipping, which is how my expert said it should be.

Think it is time to get the rings replaced.

[peterg]

So now the engine has been stripped and there is still no obvious reason for the high oil consumption. Three of the cylinders are showing carbon deposits but, apart from a ring that was cracked, no issues with the rings. The cylinders have little glazing and some of the original marks around the bore are still visible.

The oil supply to the head isn't enough for that level of consumption, so there is a lot of head scratching.

Apparently the pistons have spilts in the skirt which I know from motorcycle experience, but didn't know they were used by Bristol's.

Any sagely advice would be welcome!

[Geoff Dowdle]

petrg,
which ring was broken ?
What type of oil rings were fitted? A one piece or segmental ?
What is the clearance between pistons and bores ?
If they are one piece oil ring fit one in a bore and check the distance between the ends .
The cast split skirt pistons run tighter clearance than the original forged pistons .

Geoff