Bristol Cars - Owners and Enthusiasts Forum  

Go Back   Bristol Cars - Owners and Enthusiasts Forum > Bristol Forums > 6 cyl Bristol cars

6 cyl Bristol cars Type 400 to 406 - restoration, repair, maintenance etc

75 HP Bristol engine.

Reply
 
Thread Tools Search this Thread Display Modes
  #21 (permalink)  
Old 24-11-08, 11:22 PM
Member
 
Join Date: Jul 2008
Location: Sydney, Australia
Posts: 416
Default Tuning Solex Carburetors

Bill,
I had three 34 ICH Webers(27mm venturi)fitted to my 400 for a few years ,
they made the engine idle perfectly (the throttle shafts have seals to stop
any air leaks), preformed very well once jetted correctly but found it seem
to run lean while crusing on a feathered throttle, until I fitted a
thermostat in the cooling system to bring the water temperature from about
65 - 70 degrees up to 80 - 85 deg , then there were no further problems.
The general performance of the car did not improve greatly by changing from
Solex to Weber , except marginally at higher revs , probably due to the
larger venturis.
The Webers were very very easy to tune at idle , the idle system must be
better designed or made than the Solex .
Although I'm comparing a 55 year old set of Solex in good condition to a
new set of Weber.

Has anyone out there used 27mm ICH Webers I would like to know their
jetting ?

Regards
Geoff
Reply With Quote
  #22 (permalink)  
Old 25-11-08, 12:30 AM
BillWatkins
Guest
 
Posts: n/a
Default Tuning Solex Carburetors

Geoff:
I had 34 ICH carbs on one of my Arnolt Bristols. I can't find a record of the
size of the venturis so the jet sizes that I ran doesn't mean much. However
they were 140 Main, 240 AC & 60 Idle. They worked well for racing, but I can't
vouch for them for street use.

I looked at a chart on:

www.webernorthamerica.com/34_ICH_weber_carb.html -

and saw that it listed 29mm venturis with a range of 130 to 165 Mains
depending on whether the Aux. venturi was 4.5 or 3.5. I suggest that you take a look
there.
Bill
Reply With Quote
  #23 (permalink)  
Old 25-11-08, 04:10 PM
geo geo is offline
Member
 
Join Date: Jul 2008
Location: Orkney
Posts: 107
Default

Quote:
Originally Posted by BillWatkins View Post
In my experience, it is important to assure that there is not an air leak
around the butterfly shafts
of the Solex carburetors.

Bill Watkins
I should agree with Bill here and it is something that is so frequently overlooked: on the very-similar carb. fitted to the old two-stroke SAABs (and other old Solexes with which I have dealt) this really can be a problem that upsets the most rigorous tuning attempts, particularly when it comes to balancing multiple carbs.

If it is possible to fit new seals round the spindle (probably did not have one originally, but a suitable one might be found in the SU range if none available for the Solex) and possibly a new spindle (if worn where it makes contact with the body of the carb.), then perfection of balancing will result.

I did not envy a chum who was not getting anywhere fast attempting to balance the eight pots on a relatively modern Lagonda the other day!

George
Reply With Quote
  #24 (permalink)  
Old 12-10-09, 12:39 AM
Member
 
Join Date: Oct 2009
Location: Perth Western Australia
Posts: 2
Default 75 hp Bristol Engine

Hi, while searching for something else, I found this forum discussing the original engine 1065 from my 400/530.

Geoff wondered what was on the ID plate.
I dug the plate out of the burnt out remains and it has the engine number as 400-85-1065 stamped on it.

This may clarify, or further confuse the issue.
Nick
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


All times are GMT. The time now is 05:02 AM.


This is the live site

Search Engine Friendly URLs by vBSEO 3.6.0 PL2